MediumVulnerabilityMonitoring

Lenovo discloses XCC3 flaw that restores default root password, report says

Cyber Security News reports Lenovo disclosed CVE-2026-81936, which restores a default OpenBMC root password after an XCC reset; check firmware.

Published
Exploitation
No, the source does not report active attacks or exploitation of this flaw

Live scores

CVE-2026-81936
EPSS
0.003
low predicted chance of attack
VEDAS
0.050
little exploit evidence
On CISA KEV
Not listed
Detection rule
No public rule yet
EPSS (chance of attack)
100.1CVE-2026-81936 EPSS over time2026-112026-11-17
VEDAS (exploit evidence)
100.5CVE-2026-81936 VEDAS over time2026-112026-11-17

Thin horizontal line: the “likely exploited” threshold (EPSS 0.10, VEDAS 0.5). Shaded “no data” areas are periods when cve-scores did not publish.

What happened

According to Cyber Security News, Lenovo has disclosed a high-severity flaw in the XClarity Controller 3 (XCC3) management firmware of ThinkSystem V4 servers. The outlet reports that the flaw, tracked as CVE-2026-81936, restores a default OpenBMC root password after a factory reset of the controller. Cyber Security News says the CVE record was published on November 11, 2026, and states that Lenovo found the issue during an internal security review.

Cyber Security News reports the following details. This advisory rests on that single outlet, and we have not linked or checked the Lenovo advisory or the CVE record itself:

  • The affected releases run from XCC3 version 2.51, build IHX432Y, through version 2.56, build IHX436K.
  • Lenovo describes the cause as a development regression. Performing an “XCC Reset to Default” operation on these versions reintroduces the default OpenBMC root credential.
  • The article says the disclosure does not describe an ordinary server restart, operating system reinstall or power cycle as the trigger.
  • After the reset, an attacker could use the credential against enabled XCC administrative interfaces and reach the underlying XCC operating system. The outlet notes this is the controller’s operating system, not automatically the host operating system.
  • The weakness is classified as CWE-1392, Use of Default Credentials.
  • The record gives a CVSS 4.0 score of 7.1 (high) and a CVSS 3.1 score of 6.8 (medium). Cyber Security News says both vectors require high privileges and user interaction, so it should not be read as an unauthenticated internet takeover.

Cyber Security News says Lenovo states the affected versions are no longer available for download and that it has improved its development processes to prevent and detect similar regressions.

Not confirmed: any specific replacement firmware build (the outlet says the supplied record does not name one), and any active exploitation. The article says earlier reporting on other OpenBMC and BMC flaws does not establish exploitation of this issue.

Am I affected?

According to Cyber Security News, only a limited range of XCC3 firmware releases is affected, not every ThinkSystem server or all products that use OpenBMC. You may be affected if both of the following apply:

  • Your ThinkSystem V4 server runs XCC3 firmware from version 2.51 (build IHX432Y) through version 2.56 (build IHX436K).
  • An “XCC Reset to Default” operation has been performed, or may be performed, on that controller.

Other firmware versions, other products, and the reset history of individual controllers are not covered beyond what the source states. Anything else is not confirmed.

What to do now

  1. Identify the installed XCC3 firmware build on each ThinkSystem V4 server and compare it with the affected range reported above.
  2. Review whether any affected controllers have undergone an “XCC Reset to Default”, as the outlet says reset history matters for assessing exposure.
  3. Confirm the appropriate supported firmware with Lenovo before doing any further reset operations, since the source does not name a replacement build.
  4. Keep management access to the controllers restricted to trusted networks, as Cyber Security News advises.
  5. Use Lenovo’s security dashboard, which the outlet says can help review enabled services and account settings, but do not treat it as a substitute for checking the firmware range and getting vendor guidance.

Sources